Author: Joann Caldwell

Air sentry breathers replace a tank or reservoir’s standard breather cap or vent tube. They provide state-of-the-art contamination control protection, prolonging fluid life and reducing maintenance costs.

Contaminated air enters the hiatus and passes through a self-cleaning 2-micron solid particulate filter. Next, it is drawn through a bed of color indicating silica gel, which adsorbs moisture and water vapor from the contaminated air.

How Desiccant Breathers Work

Air sentry breathers replace existing breather caps or air vents on fluid-holding tanks, reservoirs, and gearboxes.

As a reservoir or equipment breathes, the ebb and flow of air pressure exposes the lubricants inside to the two most damaging contaminants – water vapor and dust particles. These particles can cause premature wear, degradation, and oxidation of the lubricants and equipment, leading to costly failures.

Air sentry breathers North Carolina have an isolation check valve that allows the adsorption chamber to be isolated from exhaust air and prevents exhaust from prematurely replacing the adsorbent. The adsorbent is also protected by a carbon pad that can absorb oil vapor in specific extreme environments or in cases where excessive oil mist control is required. Exhaust air also passes back through the breather’s self-cleaning 2-micron filter and partially regenerates the silica gel when it turns dark green to indicate that replacement is necessary.

How Desiccant Breathers Remove Moisture

Desiccant breathers remove moisture and particulate contaminants from the air that passes through equipment reservoirs. Unlike other contamination control systems, a desiccant breather works whether the machine is running or not. The layered system consists of a self-cleaning solid particle filter and a bed of silica gel that absorbs moisture.

Air reaches the fluid reservoir through the breather’s top cap and passes through a solid particle filter that traps any solid particles larger than 2 microns. Moisture vapor and contaminants then pass through the silica gel bed, which adsorbs any water in the air.

The solid particle filter and silica gel can be recharged or replaced, extending their effectiveness. The resulting dry, clean air can reach your machine’s fluid system, preventing contaminant buildup and prolonging fluid life. Particle

breathers prevent harmful contaminants like dust and moisture from entering industrial equipment as air is drawn in and out due to thermal expansion or fluid levels. This improves lubrication and hydraulic system life, reduces abrasive wear, and decreases maintenance and repair costs.

Desiccant breathers remove water vapor and solid particles from the air using the inherent properties of two natural substances. Silica gel adsorbs water vapor and contains microscopic pores that trap and hold up to 40% of its weight in moisture. When the silica gel has reached maximum adsorption, it turns from gold to dark green, indicating it’s time to change the pause.

The breather’s dual zone microglass media filters out the remaining moisture in the air and oil vapor, fumes, and odors. 

How Desiccant Breathers Detect Moisture

Air sentry breathers remove contaminants like dust and moisture from equipment and lubricant storage containers, helping prevent them from “breathing in” dirt and rust. This contamination control accessory reduces equipment downtime and maintenance costs, prolonging the lifespan of machinery and fluid systems.

Humid work environments shorten the breather’s lifespan, quickly causing the silica gel to reach its maximum moisture-holding capacity. To ensure the hiatus is still effective, it’s essential to select one with sufficient reservoir capacity to match your fluid system’s needs.

Gutter installation and replacement are joint home improvement projects that can often be completed within a day. Depending on the complexity of the home, the roofer will inspect the eaves and fascia board for rot or damage before beginning.

Work from a ladder rather than off the roof to reduce falls and prevent damage to gutters. Use a standoff to rest the ladder on, preventing scratches and dents.

Preparation

Gutter installation requires accurate measurements and a well-thought-out plan. This ensures you have enough materials to complete the project and prevents wasted time and money making unnecessary trips to the hardware store.

One of the most critical aspects of gutter installation is creating a fall or slope to move water toward downspouts. Ideally, gutters should have a half-inch downward slope for every ten feet of gutter run. Mark the high point of each gutter slope on the fascia board by lightly tacking a nail at the top and then marking the low end with a chalk line.

Before gutter installation Oregon City, it’s also essential to check for water damage around the home, such as rotted soffits. If you do not repair these areas, moisture can cause significant problems. This could include mold growth, wood rot, and drywall damage. To prevent this, seal all seams and joints with gutter sealant.

Materials

You need a few basic supplies when installing metal or PVC gutters. You will need gutters, downspouts, and end caps, which prevent water from splashing onto the fascia boards. You will also need elbows to transition from the gutter eavestrough to the downspout and sealant for the joints.

Aluminum gutters are famous because they resist corrosion, hold up well to dents, and are inexpensive. They are often painted in various colors to match your home’s siding.

Plastic gutters are made from several different polymers, including PVC, that can be colored throughout or in sections. They are resistant to corrosion, rust, and UV rays. They are also lightweight and require little maintenance. You can fasten these gutters with short sheet-metal screws or rivets. If you use rivets, you should permanently seal them with caulking to prevent leakage. The type of caulk used depends on your climate and roof.

Cutting

Gutters are a necessary home feature that keeps buckets of rainwater off our beautiful landscaping, away from our siding, and out of the foundation. They protect our homes from moisture damage and prevent moss and mildew growth.

A high-quality roofing professional will assess the existing gutter system and make any repairs before beginning the installation process. He will also take precise measurements of your home, including where the new gutters and downspout outlets should be positioned.

Planning for a slope in the gutter system for longer runs is essential. Planning a half-inch downslope for every ten feet of gutter run is a good rule of thumb. This will ensure that your gutters work effectively. If you are using gutter sections that overlap, use pliers to crimp the end of the upper section into the spliced side of the lower section. Then, join the two sections with self-tapping screws or rivets.

Installation

Gutters are unassuming, but they’re critical to your home. They stop buckets of rainwater from pounding your landscaping, prevent severe soil erosion around the foundation of your house, and protect your siding from discoloration.

During installation, your roofing contractor will precisely measure where new gutters should go. This helps them to ensure the gutters fit correctly and function properly.

The roofer will also look at the slant of your roof and determine how far down your gutters should extend. Gutter sections that align directly with the roof shingles impair the natural water flow. Ideally, gutters should extend out and away from the home to drain water efficiently.

When an underground oil tank is found on your property, the situation may seem overwhelming. Trying to remove it yourself could lead to severe consequences, including environmental damage and loss of home heating fuel.

However, many professional oil tank removal services can help you. Here are the key advantages of choosing an experienced company for your project.

Professional Equipment

Whether your oil tank is underground or aboveground, removing it requires special equipment. Professionals will have the right tools and machinery for the job, reducing the risk of environmental contamination and ensuring that all regulations are adhered to. The professional team will drain the tank, clean and cut it open, remove it from the ground, and take it away for proper disposal. They will also clean up any oil spills that might occur during the removal process or while transporting the tank. If you have a buried oil tank on your property, it’s in your best interest to remove it as soon as possible. It can be a severe environmental hazard and lead to expensive soil remediation if it leaks. Plus, mortgage companies often refuse to lend money to homes with leaking tanks. Removing the tank will protect you from these risks and improve the resale value of your home.

Safety

Professionals specializing in oil tank removal know how to handle potentially hazardous materials. They also follow all local regulations and guidelines regarding underground tanks, ensuring that the removal process adheres to all legal requirements. In addition, experts are familiar with the various steps involved in removing an underground oil tank, including inspecting the site and identifying any possible obstacles or problems. They also consider all relevant utility lines, preventing accidents or issues that could impact the process. Lastly, professional oil tank removal Westchester County NY, services are experienced in working with state authorities to close tanks in place. In many cases, simply digging a hole and filling it with sand doesn’t meet the state’s requirements to prove that the tank was closed correctly. This can lead to future contamination cleanup costs for the seller or buyer of the property, as well as the potential for environmental liability. Professionals can help property owners earn a “No Further Action” letter to avoid these issues.

Peace of Mind

If you are a homeowner, having an old underground oil tank can be very stressful. When you hire a professional service, you can ensure the project will be completed within a few hours. You can then enjoy peace of mind knowing that your property is no longer a liability and will not face any issues when it comes time to sell your home. You may even get a lower insurance premium after the project, as your property will be officially oil-tank-free. It is essential to choose a firm that is licensed for both closure (removal) and testing, as this will help you avoid any potential problems.

Experience

Professional oil tank removal companies have been in business for years, so they know what to do and how to handle the job. This experience translates into more accurate, efficient, and cost-effective work. One of the main problems associated with underground oil tanks is that they can leak. This can lead to soil and groundwater contamination that poses significant environmental risks. Fortunately, when professionals remove an old oil tank, this helps to minimize the risk of contamination. It’s also worth noting that many mortgage lenders won’t approve loan applications from homeowners who have a leaking underground oil tank on their property. This is why homeowners must have their oil tanks appropriately removed before selling the property. It’s also a good idea to have an underground oil tank removed if you are planning any home improvement projects. This way, you can ensure that the renovations won’t be damaged by the digging required to remove the oil tank.